1 C CMS530.noname1 E7.2 /GICWINSHOP 21.09.2018 15:36:58 <M1> 6.8.035 Build 1 Release (gb) #139=566 #156=0 <SETUP2>
11 C NP1=9.0 Setup Row
12 C NP2=11.0 Tubular Cycle front
13 C NP3=11.0 Tubular Cycle rear
14 C NP4=9.5 Transition-RR
15 C NP5=12.0 Struc Single jersey front
16 C NP6=12.0 Struc Single jersey rear
17 C NP11=7.0 Setup Row front
18 C NP17=12.0 Safety rows
19 C NP20=9.0 Start 1
20 C NP21=10.0 Start 2
21 C NP22=11.0 Start 3
22 C NP23=11.5 Start 4
23 C NP24=12.0 Start 5
24 C NP25=18.0 Comb Thread
25 C MSECI=0.70
39 IF #L=0 #L=1 IF #R=0 #R=699 #LM=0 #RM=0
40 START
41 C #98=0 C Cast-off On/Off (#98=0)
42 C #69=0 C MS*#69 (1-4s) (#69=1..4)
43 PF0
44 Y-CR1
50 YGC:1F=A 2F=B/2F=C 8F=D;
51 YDF=2
52 C------------------------------------I------------------------------------I
53 C LEFT I RIGHT I
54 C------------------------------------I------------------------------------I
55 C I 8=D Protection thread 1 I
56 C 2=B Comb thread1 I 2=C Rib thread 1 I
57 C 1=A Draw thread1 I I
58 C------------------------------------I------------------------------------I
59 YD YC
80 FBEG:M1-SIZES;
81 F1=1-699
82 PA:JA1; PAI:JA1;
83 PM:1:F1; SEN=1-699 #51=1 #52=699
84 Y-2B:HR1G;
85 FEND C M1-SIZES
86 JA1=1320(1100-1100)
110 #99=0
111 IF RS17=0 S0Y #99=1 W0
112 IF RS17=1 S0YCR0 #99=1 W0
113 IF #99=1 #99=0 MS PRINT/CHECK YARN CARRIER/
114 F:M1-SINTRAL;
115 END
116 FBEG:M1-SINTRAL;
117 IF RS17=0 F:SWITCH-1; C Comb On/Off
118 IF RS17=0 F:SWITCH-4; C Comb On/Off
119 JA1=1310 #L=276 #LM=0 #RM=0 #R=425
120 << S:<1-><+>A(21)-Y(21); Y:=D; VU V0 Y-8A:F1+^0; YC Y-8A:YD1.0-1.0; S3 W+F50 W0 MSEC3
121 IF RS17=0 F:SWITCH-5; C Comb On/Off
122 JA1=1285 #L=276 #LM=0 #RM=0 #R=425
123 F:M1-SIZES;
124 >> S:<1-><+>A(22)-Y(22); Y:=D; VU V0 Y-8A:F1+^0; YC Y-8A:YD1.0-1.0; S1 WMF1 MSEC3
125 IF RS15<>0 F:CYCLE-8; C Protection thread
126 JA1=1282 #L=276 #LM=0 #RM=0 #R=425
127 << S:<1->UVS+/<1->UVS+/<1-><+>AH(23)-H(21); Y:=D; V0 YC S1 S2 Y-8A:F1+^0; Y-8A:YD1.0-1.0; S3 WMF1 MSEC3
128 >> S:<1-><+>AH(23)-H(21)/<1->%*-*/<1-><B>A(24)-0; Y:=D/0/=A; Y-8A:YD1.0-13.0; S1 S2 Y-1A:F1B^0; Y-1A:YD7.0-1.0; S3
129 << S:<1-><B>A(24)-0/<1-><A>H(1)-H(11); Y:=A/=C; S1 Y-2B:HL1 HR1 F1A^0; Y-2B:YD1.0-7.0; S2
130 >> S:<1-><A>A(2)-0; Y:=C; Y-2B:YD1.0-1.0; S2
131 << S:<1-><A>0-Y(3); Y:=C; S2
132 >> S:<1-><A>A(2)-0; Y:=C; S2
133 IF RS1<>0 F:CYCLE-9; C Tubular Cycle
134 JA1=1269 #L=276 #LM=0 #RM=0 #R=425
135 << S:<1-><A>0-Y(3); Y:=C; V0 Y-2B:HL1 HR1 F1A^0; YC Y-2B:YD1.0-1.0; S2 WMF1 MSEC3
136 >> S:<1-><A>H(4)-H(4); Y:=C; S2
137 SBEG
138 Y-2A:HL0 HR0 F1*^0;
139 IF RS17=0 Y-2A:C; V0 YC S1
140 << S:<1->UVS+/<1->UVS+; V0 S2 S3
141 SEND
142 >> VU S0 W0
143 << S:<1-><A>A(5)-0; Y:=C; VU S3 WMF1 W+F1 MSEC2
144 REP*74
145 >> S:<1-><A>A(5)-0; Y:=C; VU S1
146 << S:<1-><A>A(5)-0; Y:=C; VU S3
147 REPEND
148 >> S:<1-><A>A(5)-0; Y:=C; VU S1
149 REP*5
150 << S:<1-><A>A(17)-0; Y:=C; VU S3
151 >> S:<1-><A>A(17)-0; Y:=C; VU S1
152 REPEND
153 << S:<1-><A>A(17)-0; Y:=C; VU S3
154 RS17=1 IF #100=1 RS17=0
155 >> S:<1-><A>A(17)-0; Y:=C; VU Y-2B:HL0 HR1; S1
156 IF RS17=0 F:SWITCH-10; C Cast off
157 FEND C M1-SINTRAL
158 C ---------- Comb On/Off ----------
159 FBEG:SWITCH-1;
160 IF #98=0 F:SWITCH-2; C Cast-off On/Off
161 IF #140=1 F:SWITCH-3; GOTO #123 C Comb of lower Limit Switch
162 JA1=1318 #L=1 #LM=0 #RM=0 #R=699
163 IF#99=1 #99=0 MS PRINT/! ! CHECK COMB ! !/
164 << V0 =-= S0 WMF2 MSEC=0.70 LK1
165 IFN#137=72 MS PRINT/! ! INVALID GAUGE ! !/
166 >> S:<1-><*>A(25)-Y(25)/<1->H(20)-H(20); Y:=B/0; Y-2A:HL0 HR1 R25 F1*^0; Y-2A:YD-1.0; #R<273 S2 S3
167 << S:<1-><*>A(25)-Y(25)/<1->H(20)-H(20); Y:=B!/0; Y-2A:HL2 HR1; S1 S2
168 =^= #98=0 VU
169 >> S0 W0
170 FEND C Comb On/Off
171 C ---------- Cast-off On/Off ----------
172 FBEG:SWITCH-2;
173 JA1=1320 #L=1 #LM=0 #RM=0 #R=699
174 AS1
175 << S0 W0
176 >> S:<1->H(20)-H(20); Y:0; S1 WMF3 MSEC=1.00
177 << S:<1->H-H; Y:0; V0 S1 WMF2
178 AS0
179 >> S0
180 FEND C Cast-off On/Off
181 C ---------- Comb of lower Limit Switch ----------
182 FBEG:SWITCH-3;
183 JA1=1318 #L=1 #LM=0 #RM=0 #R=699
184 << V0 S0 WMF2 MSEC=1.00
185 #99=1
186 >> S0
187 FEND C Comb of lower Limit Switch
188 C ---------- Comb On/Off ----------
189 FBEG:SWITCH-4;
190 JA1=1314 #L=276 #LM=0 #RM=0 #R=425
191 << S:<1->UXST-+/<1-><+>N.-0; Y:=D; V0 S2 Y-8A:F1+^0; S3 W0 MSEC3
192 >> VU #R>274 S0 W0
193 << S:<1->UXST%A-+%Y; S3 W0 MSEC3
194 >> S:<1-><+>A(21)-Y(21); Y:=D; VU Y-8A:YD-1.0; #R<274 S1 W0
195 FEND C Comb On/Off
196 C ---------- Comb On/Off ----------
197 FBEG:SWITCH-5;
198 JA1=1309 #L=276 #LM=0 #RM=0 #R=425
199 >> S:<1->UXST-+/<1-><+>A(21)-Y(21)/<1->UVS+; Y:=D; V0 YC S1 Y-8A:F1+^0; Y-8A:YD1.0-1.0; S2 S3 W0 MSEC3
200 << S:<1-><+>A-0/<1-><A>N.-0; Y:=D/=C; VU S1 Y-2B:HL0 HR1 F1A^0; S2 W0
201 >> VU #R>274 S0 W0
202 << S:<1->UXST%A-+%Y/<1->A-Y; Y:0; S1 S2 W0
203 >> S:<1-><A>A-0/<1-><+>A-Y/<1->UXST-+; Y:=C/=D; Y-2B:YD-7.0; #R<274 S1 S2 S3 W0
204 << S:<1-><+>A-Y/<1->UVS+; Y:=D; S2 S3 W0
205 Y-RALL
206 >> S:<1-><+>A-0/<1-><B>N.-0; Y:=D/=A; VU S1 Y-1A:F1B^0; S2 W0
207 << VU #L<275 S0 W0
208 >> S:<1->UXST%A-+%Y/<1->A-Y; Y:0; S1 S2 W0
209 << S:<1-><B>0-Y; Y:=A; VU Y-1A:YD7.0; #L>275 S2 W0
210 >> VU S0 W0
211 IF RS18=>1 IF RS18<=5 F:SWITCH-6; C Compensation Float and Lock
212 JA1=1286 #L=276 #LM=0 #RM=0 #R=425
213 Y-RALL
214 << S:<1-><+>A(21)-Y(21); Y:=D; VU V0 Y-8A:F1+^0; YC Y-8A:YD1.0-45.0; S3 W0 MSEC3
215 FEND C Comb On/Off
216 C ---------- Compensation Float and Lock ----------
217 FBEG:SWITCH-6;
218 JA1=1292 #L=276 #LM=0 #RM=0 #R=425
219 << S:<1-><+>N.-0; Y:=D; VU V0 Y-8A:F1+^0; YC Y-8A:YD45.0-1.0; S3 W0 MSEC3
220 >> S:<1-><+>A(21)-Y(21); Y:=D; VU Y-8A:YD45.0-45.0; S1 WMF1
221 IF RS18<>0 F:CYCLE-7; C Compensation Float and Lock
222 JA1=1288 #L=276 #LM=0 #RM=0 #R=425
223 << S:<1-><+>A(21)-Y(21); Y:=D; VU V0 Y-8A:F1+^0; YC Y-8A:YD45.0-45.0; S3 WMF1 MSEC3
224 >> S:<1-><+>N.-0; Y:=D; VU S1 W0
225 FEND C Compensation Float and Lock
226 C ---------- Compensation Float and Lock ----------
227 FBEG:CYCLE-7;
228 RBEG*RS18
229 JA1=1290 #L=276 #LM=0 #RM=0 #R=425
230 << S:<1-><+>A(21)-Y(21); Y:=D; VU V0 Y-8A:F1+^0; YC Y-8A:YD45.0-45.0; S3 WMF1 MSEC3
231 >> S:<1-><+>A(21)-Y(21); Y:=D; VU S1
232 REND
233 FEND C Compensation Float and Lock
234 C ---------- Protection thread ----------
235 FBEG:CYCLE-8;
236 RBEG*RS15
237 JA1=1284 #L=276 #LM=0 #RM=0 #R=425
238 << S:<1-><+>A(22)-Y(22); Y:=D; VU V0 Y-8A:F1+^0; YC Y-8A:YD1.0-1.0; S3 WMF1 MSEC3
239 >> S:<1-><+>A(22)-Y(22); Y:=D; VU S1
240 REND
241 FEND C Protection thread
242 C ---------- Tubular Cycle ----------
243 FBEG:CYCLE-9;
244 RBEG*RS1
245 JA1=1271 #L=276 #LM=0 #RM=0 #R=425
246 << S:<1-><A>0-Y(3); Y:=C; V0 Y-2B:HL1 HR1 F1A^0; YC Y-2B:YD1.0-1.0; S2 WMF1 MSEC3
247 >> S:<1-><A>A(2)-0; Y:=C; S2
248 REND
249 FEND C Tubular Cycle
250 C ---------- Cast off ----------
251 FBEG:SWITCH-10;
252 JA1=1103 #L=276 #LM=0 #RM=0 #R=425
253 << Y-1A:C; V0 S1 MSEC=0.70 W0
254 >> Y-8A:C; S1Y-2B:C; S2 W0
255 << S:<1->H(17)-H(17)/<1->H-H; Y:0/0; S1 S2 WMF4
256 #98=1
257 >> S:<1->H-H/<1->H-H; Y:0/0; S2 S3 WMF2 MS=2.5
258 IF #69=>1 IF #69<=4 F:SWITCH-11; C MS*#69 (1-4s)
259 FEND C Cast off
260 C ---------- MS*#69 (1-4s) ----------
261 FBEG:SWITCH-11;
262 JA1=1100 #L=276 #LM=0 #RM=0 #R=425
263 << V0 YC S0 WMF2 MSEC=0.70
264 IF#69=1 MS=1
265 IF#69=2 MS=2
266 IF#69=3 MS=3
267 IF#69=4 MS=4
268 >> S0
269 FEND C MS*#69 (1-4s)
999 S0 W0
iakähkönen
Knitwear development
From hands-on programming and sample development to sharper techpacks and development strategy, I turn knitwear ideas into clear, testable outcomes.
Explore the support available for your project.
Read more
Knitwear education
Through team training, teaching and programmer mentoring, I turn specialist knitwear knowledge into practical skills that can be applied directly to development work.
Explore the learning support available for your team or professional development.
Read moreDesigner's
eyeProgrammer's logicMaterial knowledge
“A designer’s eye, a programmer’s logic, and deep material knowledge shape my approach — helping creative ideas become technically achievable knitwear.”
What clients say
“Ia is an exceptional programmer, and working with her, I could trust that all my complex knitwear design ideas were executed exactly as I intended. She is a great problem solver, and her background in design made communication easy from start to finish. Her technical proficiency combined with an eye for detail makes her one of my favorite development partners.”
Resume
